Fig.: Garmin BlueChart G1 Stick
Garmin used a proprietary nautical chart memory stick called the BlueChart G1 for its old plotters. The memory sticks are available in sizes from 8…512 MB. The stick consists of two memory modules that have a 16-bit data interface and can exchange data with the electronics of the plotter. Back then, Garmin offered sticks with nautical charts that could only be read. But there were also writable memory sticks to which you could transfer sea charts yourself with the help of a USB card reader and the Windows software MapSource. In order for MapSource to be able to recognize the USB card reader, special drivers are required which are only available for WinXP and WinVista. With newer operating systems such as Win7, Win10 or Win11, the old 32-bit drivers no longer work and you have to use one of the two old operating systems. However, you have to keep one thing in mind. The memory stick is not integrated as a normal drive in Windows. MapSource is required for data exchange.
Fig.: Garmin USB Data Card Programmer
The correct installation of the driver for the USB Data Card Programmer is error-prone, since several drivers have to be loaded one after the other in the correct order. The following conditions must be met in order to use the USB Data Card Programmer under MapSource:
- Garmin USB Data Card Programmer (USB 1.0)
- Memory stick 8…256 MB (512 MB are not supported)
- Operating system WinXP with SP3 or WinVista
- DotNet Framework 3.5
- Garmin driver software V2.3.1.2
- MapSource V6.1.6.3
- ActivSync must be disabled in Windows
Table of contents
installation Guide
The installation guide is based on a revised version of this website by Kurt Löffler from Vienna.
Since October 2015 there is the last and therefore current Garmin USB driver with the version 2.3.1.2 and this replaces all previous Garmin USB drivers. This is currently (as of October 2022) still the current Garmin USB driver for the Garmin USB Data Card Programmer.
Step 1
The Garmin USB driver can be downloaded here:
https://www8.garmin.com/support/download_details.jsp?id=591
This USB driver V2.3.1.2 also supports 64-bit operating systems from WinXP and WinVista. But only for Garmin USB GPS devices! The USB Data Card Programmer is not supported by 64 bit operating systems supports!
Download USB driver V2.3.1.2 and save it on the hard disk.
step 2
Garmin USB driver installation
In this step, no Garmin USB device may be connected to the PC! Disconnect all Garmin USB devices before beginning the installation of the Garmin USB driver! Then double-click the .exe file and follow the installation instructions. After successful installation of the Garmin USB driver, be sure to shut down and switch off the PC!
Again very important see above:
First, just double-click the driver.exe file WITHOUT that a Garmin GPS device is connected!
After successful driver installation only step 2 is completed!
step 3
PC wieder neu einschalten und hochfahren und im Schritt 3 der Garmin USB Treiberinstallation fortfahren. Erst jetzt darf der Garmin USB Data Card Programmer erstmalig wieder an einen freien USB Port vom PC angesteckt werden! Es erfolgt sofort vom PC die Meldung „Neue Hardware“ gefunden und der Geräteassistent wird sich öffnen und Schritt 3 beginnt.
Step 2 was installing the Garmin USB driver WITHOUT that a Garmin USB device was plugged in. After plugging in the Garmin USB Data Card Programmer, the hardware wizard will open as shown in the picture above. select option Install software automatically (1.) and with Continue (2.) to the next window.
In the picture, the USB driver previously installed in step 2 is loaded for the Garmin USB Data Card Programmer, which was now connected in step 3.
At the end the window appears that a driver for the Garmin USB Data Card Programmer has been installed. on Complete (1.) click!
!!! And this is where most people start making a mistake!!!
It appears after clicking on top Complete at the bottom of the Windows task bar again the info New hardware found. Please do it! This is not an endless loop but the continuation of the further installation so that it is complete!
Das ist kein Fehler! Es wird sich abermals der Hardwareassistent öffnen, siehe Bild ganz oben und anzeigen das eine „neue Hardware“ gefunden wurde! Und hier brechen die meisten leider ab, da sie denken: „Hab ich doch gerade gemacht“! Und das ist ein Fehler.
Please be sure to run through the whole process again as described in the picture at the top!!!
Es kann sein das bis zu DREI MAL (!!!) der Hardwareassistent eine „Neue Hardware“ meldet!
That is correct! Sometimes 3 different Garmin drivers have to be loaded! And this happens every time the hardware wizard opens.
Only when the following lights up in the Windows taskbar at the bottom right: „Die neue Hardware wurde installiert und kann jetzt verwendet werden“ – Erst dann ist die Treiberinstallation Completely completed for the Garmin USB Data Card Programmer.
Also nicht ungeduldig werden und genau schauen was der PC rechts unten schreibt! Spätestens nach dem dritten Durchlauf vom Hardwareassistenten kommt die Meldung „Die neue Hardware wurde installiert und kann jetzt verwendet werden“. Erst jetzt steht der Garmin USB Data Card Programmer im Programm MapSource zur Verfügung und seine Installation ist jetzt korrekt und vollständig abgeschlossen!
| An important note, since the question keeps coming up The Garmin USB card reader will Not als „Laufwerk“ am Arbeitsplatz angezeigt! Viele glauben daher das die Installation nicht funktioniert hat, das ist aber ein Irrglaube und falsch. Der Garmin USB-Card Reader erscheint nur im Gerätemanager! „Start“ – „Systemsteuerung“ – „System“ – dort den Gerätemanager öffnen. Er ist dort als „Garmin Device“ eingetragen.  |
On the plus sign GARMIN devices klicken. Dann öffnet sich der Eintrag vom Garmin USB Data Card Programmer wie oben im Bild im roten Kreis. Diesen Eintrag mit der linken Maustaste anklicken damit er blau markiert wird so wie oben im Bild zu sehen. Den Mauszeiger ebenfalls auf den jetzt blau markierten Eintrag stellen und die rechte Maustaste drücken. In dem sich öffnenden Kontexmenü den Eintrag „Eigenschaften“ auswählen. Es öffnet sich jetzt das Fenster mit den Eigenschaften vom Garmin USB Data Card Programmer.
In the register tab General, see picture above, the Garmin Data Card Programmer is now shown as ready for use. The USB driver installation was successful. The Garmin USB Data Card Programmer is now ready to use.
step 4
The MapSource program can now be started. Select a map tile with the tool map function (the yellow polygon) and click on a tile. This is now highlighted in pink and the name of the tile appears in the tab on the left cards from MapSource. Now on Send to device click.
The MapSource window opens Send to device, see picture above. Then open the selection window (1.), the list (2.) opens with the possible memory locations on the PC. The entry USB programming device for memory cards (2.) Select, click with the left mouse button so that the entry is marked in blue, as can be seen in the picture above. The Garmin USB Data Card Programmer is now selected and by clicking on the button Send (3.) the transfer of the maps to the Garmin data chip begins.
Annotation:
In the picture above the as Removable disk drive letters L through O marked devices are card readers in the PC for the memory cards of the digital camera - i.e. SD, CF, memory stick, xD card, etc., etc. Here, too, a note to those who allegedly do not transfer any card tiles to the SD/CF cards, etc be able. The new Garmins have normal SD card memory cards. You absolutely have to open the selection window, as shown in the picture above, and select the correct drive letter (card slot of your reader!) from the list in which the respective memory card is inserted, so that MapSource can transfer the map tiles correctly! Often the mistake is made and it becomes a Removable data medium used and up Send clicked without first checking whether the correct card slot of the reader was selected in the list!